Kia Picanto (JA): Exhaust Emission Control System / Catalytic Converter

Description and operation

Description
The catalytic converter of the gasoline engine is a three way catalyst. It oxidizes carbon monoxide and hydrocarbons (HC), and separates oxygen from the oxides of nitrogen (NOx).

Repair procedures

Removal
[WCC]
1.
Remove the engine room under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
2.
Drain the engine coolant.
(Refer to Engine Mechanical System - "Coolant")
3.
Remove the air cleaner assembly.
(Refer to Engine Mechanical System - "Air Cleaner")
4.
Remove the front muffler.
(Refer to Engine Mechanical System - "Muffler")
5.
Disconnect the electric waste gate actuator (EWGA) extension connector (A).

6.
Remove the front oxygen sensor.
(Refer to Engine Control / Fuel System - "Heated Oxygen Sensor (HO2S)")
7.
Disconnect the water hose (A).

8.
Disconnect the turbo charger water drain pipe hose (A).

9.
Remove the coupler heat protector (A) and water drain pipe (B)
Tightening torque
Heat protector mounting bolt :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
(If equipped with a cap, tighten it until the cap is removed.)
Eye bolt :
26.4 - 32.3 N·m (2.7 - 3.3 kgf·m, 19.5 - 32.3 lb·ft)Pipe mounting
Bolt :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

10.
Remove the exhaust manifold stay (A).
Tightening torque :
39.2 - 44.1 N·m (4.0 - 4.5 kgf·m, 28.9 - 32.5 lb·ft)

11.
Remove the warm-up catalytic converter (WCC) upper stay (A) and then remove the warm-up catalytic converter (WCC) (B).
Tightening torque
Warm-up catalytic converter (WCC) :
49.0 - 53.9 N·m (5.0 - 5.5 kgf·m, 36.1 - 39.7 lb·ft)
Warm-up catalytic converter (WCC) upper stay :
18.6 - 23.5 N·m (1.9 - 2.4 kgf·m, 13.7 - 17.4 lb·ft)

Installation
1.
Install in the reverse order of removal.

    Description and operation Description The Gasoline Particulate Filter (GPF) system prevents Particulate Matter (PM) from being discharged to the atmosphere and consists of a filter assembly, two Exhaust Gas Temperature Sensors (EGTS).

    Description and operation Description Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valves in accordance with the ECM control signal calculated by the engine speed and load.

    Other information:

    Kia Picanto (JA) 2017-2026 Service & Repair Manual: Power Door Lock Module

    Components and components location Components 1. Door lock/unlock knob cable 2. Door inside handle cable 3. Door latch assembly Repair procedures Inspection    • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to

    Kia Picanto (JA) 2017-2026 Service & Repair Manual: Smart Key

    Repair procedures Smart Key Smart Key Code Saving 1. Connect the DLC cable of KDS/GDS to the data link connector (16 pins) in driver side crash pad lower panel, turn the power on KDS/GDS. 2. Select the vehicle model and then do "Smart key code saving".

    Categories

     
    Copyright © 2026 www.kpicanto.com - 0.0357