Kia Picanto JA: AVN System / Speaker

Kia Picanto (JA) 2017-{YEAR} Service & Repair Manual / Body Electrical System / AVN System / Speaker

Repair procedures
Inspection
Troubleshooting of the speakers
   
When handling the speakers :
Do not cause shock to the speakers by dropping or throwing them.
Be careful not to drop water and oil on the speakers.
Use caution to handle the speaker because diaphragm made of paper is easily torn by impact or external force.
Audio system tuning may cause damage to the speakers. The modified speakers are not covered by the manufacturer’s warranty.
1.
Basic inspection
Loosen the screws to rule out the interference from the body trims and surrounding parts and then remove the speaker.
After removing the speaker, check the sound quality of the speaker with the connector plugged in.
2.
Inspection for each cause
(1)
Abnormal vibration
Make sure the mounting screws are properly tightened before replacing the speaker.
Reinstall the speaker and check that the symptom is resolved.
If the symptom does not disappear, replace the speaker with a new one.
(2)
Noise
Check that the speaker connector is properly connected and reinstall the connector if necessary.
If noises occur in the radio mode, turn to the CD player mode.
If noises occur in both modes, replace the speaker with a new one.
   
If noises occur only in the radio mode, the poor radio reception is the cause so do not replace the speaker.
(3)
Poor working
Check the plus (+) and negative (-) speaker terminals using an ohmmeter.
If resistance is measured at the specified value shown below, the speaker operation is normal.
If the measured resistance is different from the specified value, replace the speaker.

Removal
Front Door Speaker
1.
Disconnect the negative (-) battery terminal.
2.
Remove the front door trim.
(Refer to Body - "Front Door Trim")
3.
Remove the front door speaker (B) after disconnecting the connector (A) and loosening the screws.

Tweeter Speaker
1.
Disconnect the negative (-) battery terminal.
2.
Using a screwdriver or remover, remove the front door quadrant inner cover (A).

3.
Disconnect the tweeter speaker connector (A).

4.
Remove the tweeter speaker (A) after loosening the mounting screws.

Rear Door Speaker
1.
Disconnect the negative (-) battery terminal.
2.
Remove the rear door trim.
(Refer to Body - "Rear Door Trim")
3.
Remove the rear door speaker (B) after disconnecting the connector (A) and loosening the screws.

Installation
Front Door Speaker
1.
Install the front door speaker.
2.
Install the front door trim.
3.
Connect the negative (-) battery terminal.
Tweeter Speaker
1.
Install the tweeter speaker.
2.
Install the front door quadrant inner cover.
3.
Connect the negative (-) battery terminal.
Rear Door Speaker
1.
Install the rear door speaker.
2.
Install the rear door trim.
3.
Connect the negative (-) battery terminal.
   
Make sure that the speaker connectors are plugged in properly.
Check the AVN system for normal operation.

    AVN(Audio Video Navigation) head unit

    Components and components location Components Connector Pin Information No. Connector A Connector B 1 Rear door left speaker (+) - 2 Rear door left speaker (-) MIC (+) 3 - - 4 - - 5 - Antenna power 6 Camera power Illumination (+) 7 Camera video Non E-Call type : - E-Call type : Multmedia-CAN (High) 8 - - 9 - ALT Left_output (-) 10 AUX Audio_right input Battery (+) 11 AUX Detect Battery (+) 12 Steering wheel remote controller Ground 13 Front door left speaker (+) Ground 14 Front door left speaker (-) - 15 Front door right speaker (-) MIC (-) 16 Front door right speaker (+) - 17 - - 18 - - 19 - Default : Ground Option : Illumination (-) 20 Camera power_Ground Non E-Call type : - E-Call type : Multmedia-CAN (Low) 21 Camera video_Ground - 22 - ACC 23 - - 24 AUX Audio_left input - 25 AUX Audio_Ground Reverse 26 Steering wheel remote controller (Ground) Door open 27 Rear door right speaker (-) Door unlock status 28 Rear door right speaker (+) Parking brake 29 - 'P' Position 30 - Auto light 31 - - 32 - - 33 Camera shield_Ground IGN1 34 - - 35 - - 36 - 37 - 38 Vehicle speed Repair procedures Removal    • Be careful not to scratch the center fascia upper panel and related parts...

    AVN Antenna

    Components and components location Components [Roof Antenna (Radio+GPS/GNSS+DAB+GSM)] Repair procedures Removal Roof antenna 1...

    Other information:

    Kia Picanto (JA) 2017-2025 Service & Repair Manual: Headlamp Leveling Switch


    Schematic diagrams Circuit Diagram Repair procedures Removal 1.Disconnect the negative (-) battery terminal. 2.Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel") 3.Remove the crash pad side switch (A) after loosening the mounting screws...

    Kia Picanto (JA) 2017-2025 Service & Repair Manual: Front Seat Frame Assembly


    Components and components location Component Location 1. Front seat back frame assembly 2. Front seat cushion frame assembly Repair procedures Replacement    • Put on gloves to protect your hands...

    Categories

    Windshield defrosting and defogging

    WARNING

    Windshield heating

    Do not use the or position during cooling operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield could cause the outer surface of the windshield to fog up, causing loss of visibility. In this case, set the mode selection knob or button to the position and fan speed control knob or button to the lower speed.

    For maximum defrosting, set the temperature control to the extreme right/hot position and the fan speed control to the highest speed. If warm air to the floor is desired while defrosting or defogging, set the mode to the floor-defrost position. Before driving, clear all snow and ice from the windshield, rear window, outside rear view mirrors, and all side windows. Clear all snow and ice from the hood and air inlet in the cowl grill to improve heater and defroster efficiency and to reduce the probability of fogging up the inside of the windshield.

    read more

     
    Copyright © 2025 www.kpicanto.com