Kia Picanto: Engine Control System / Heated Oxygen Sensor (HO2S)
Specifications
HO2S [Bank 1/Sensor 1]
Item
|
Specification
|
Heater Resistance (Ω)
| 2.5 - 4.0 [20°C(68°F)]
|
Type
| Linear
|
Pin
| 6
|
HO2S [Bank 1/Sensor 2]
Item
|
Specification
|
Heater Resistance (Ω)
| Approximately 9.0 [20°C(68°F)]
|
Type
| Binary
|
Pin
| 4
|
Description and operation
Installed
in both upstream and downstream of the Manifold Catalytic Converter,
the Heated Oxygen Sensor (HO2S) consists of zirconium and alumina. The
sensor output voltage varies in accordance with the air fuel ratio.
The
sensor must be heated in order to operate properly. To keep it heated,
it is equipped with a heater controlled by the ECM via a duty cycle
signal. When the exhaust gas temperature is lower than the specified
value, the heater will warm up the sensor tip.
Schematic diagrams
Repair procedures
| 1. | Turn the ignition switch OFF. |
| 2. | Disconnect the HO2S connector. |
| 3. | Measure resistance between the HO2S terminals 2 and 5 [B1/S1].
Specification : 2.4-4.0 [20°C(68°F)] |
|
| 4. | Measure resistance between the HO2S terminals 3 and 4 [B1/S2].
Specification : Approximately 9.0 [20°C(68°F)] |
|
| 5. | Check that the resistance is within the specification. |
Note that the SST 09392-1Y100 can be used for removing the heated oxygen sensor. |
| 1. | Turn the ignition switch OFF and disconnect the battery negative (-) terminal. |
| 2. | Disconnect the connector (A). |
| 3. | Remove the heated oxygen sensor (B).
Heated oxygen sensor:
39.2 - 49.1 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft) |
 |
| 1. | Turn the ignition switch OFF and disconnect the battery negative (-) terminal. |
| 2. | Disconnect the connector (A).
 |
| 3. | Remove the heated oxygen sensor (A).
Heated oxygen sensor:
39.2 - 49.1 N·m (4.0 - 5.0 kgf·m, 28.9 - 36.2 lb·ft) |
 |
| •
| Install the component to the specified torques. |
| •
| Note
that internal damage may occur when the component is dropped. If the
component has been dropped, inspect before installing. |
| •
| DO
NOT use a cleaner, spray, or grease to sensing element and connector of
the sensor as oil substance may degrade the sensor performance. |
| •
| Sensor and its wiring may get damaged by contacting with the exhaust system (Exhaust Manifold, Catalytic Converter, etc.). |
|
| 1. | Install in the reverse order of removal. |
Specifications
Specification
Item
Specification
Resistance(MΩ) 4.87 Capacitance (pF) 850 - 1150 Type Piezo-electricity Pin 2
...
Specifications
Specification
Exhaust Gas Temperature Sensor (EGTS) #1, 2
▷ Type : Thermistor type
Temperature [°C (°F)]
Resistance ( ...
Other information:
Tire traction
Tire traction can be reduced if you drive
on worn tires, tires that are improperly
inflated or on slippery road surfaces.
Tires should be replaced when tread
wear indicators appear. Slow down
whenever there is rain, snow or ice on
the road to reduce the possibility of
lo ...
Components and components location
Component
Repair procedures
Removal
1.Disconnect the negative(-) battery terminal.
2.Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
3.Remove the steering column upper and lower shrouds.
...
Knock Sensor (KS)
Exhaust Gas Temperature Sensor (EGTS)