Kia Picanto: Rear Seat / Rear Seat Back Cover

Kia Picanto JA 2017-2023 Service & Repair Manual / Body (Interior and Exterior) / Rear Seat / Rear Seat Back Cover

Components and components location

Component Location

1. Rear seat back cover [RH]

2. Rear seat back cover [LH]

Repair procedures

Replacement

Put on gloves to protect your hands.

•	Use a plastic panel removal tool to remove interior trim pieces without marring the surface.

•	Be careful not to bend or scratch the trim and panels.

[LH]

1.	Remove the rear seat assembly. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pin and remove the rear seat headrest (A).

3.	Remove the bezel upper cover (A) by using a remover.

4.	Remove the rear seat back webbing guide (A) by using a remover.

5.	Remove the child anchor cover (A) by using a remover.

6.	Detach the rear seat back dust cover (A).

7.	Remove the rear seat lower mounting hog-ring clips (A).

8.	Open the seat back side zipper (A). [LH] [LH]

9.	Detach the rear seat back cover mounting hook(A).

10.	Remove the back board (A) after removing the hog-ring clips.

11.	Detach the rear seat back cover side mounting hook(A).

12.	Push the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

13.	Remove the rear seat back cover from the frame.

14.	Remove the front seat back covering (C) after removing the velcro tape (A) and hog-ring clip (B).

15.

Install in the reverse order of removal.

•	Make sure that the connectors are connected completely.

•	Replace any damaged clips (or pin - type retainers).

•	To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog - ring clips (A).

•	Replace the hog-ring clips with new ones using special tool (C) (09880 - 4F000).

[RH]

1.	Remove the rear seat assembly. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Push the lock pin and remove the rear seat headrest (A).

3.	Remove the bezel upper cover (A) by using a remover.

4.	Remove the child anchor cover (A) by using a remover.

5.	Detach the rear seat back dust cover (A).

6.	Remove the rear seat lower mounting hog-ring clips (A).

7.	Open the seat back side zipper (A). [LH] [LH]

8.	Detach the rear seat back cover mounting hook(A).

9.	Remove the back board (A) after removing the hog-ring clips.

10.	Detach the rear seat back cover side mounting hook(A).

11.	Push the rear seat headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.

12.	Remove the rear seat back cover from the frame.

13.	Remove the front seat back covering (C) after removing the velcro tape (A) and hog-ring clip (B).

14.

Install in the reverse order of removal.

•	Make sure that the connectors are connected completely.

•	Replace any damaged clips (or pin - type retainers).

•	To prevent wrinkles, make sure that the cover (B) is stretched evenly before connecting the hog - ring clips (A).

•	Replace the hog-ring clips with new ones using special tool (C) (09880 - 4F000).

Rear Seat Assembly

Components and components location Component Location 1. Rear seat cushion assembly 2. Rear seat back assembly Repair procedures Replacement ...

Rear Seat Cushion Cover

Components and components location Component Location 1. Rear seat cushion cover Repair procedures Replacement Put on gloves to protect your h ...

Other information:

Kia Picanto JA 2017-2023 Owner's Manual: Increase cargo space

If you want to increase cargo space, 1. Grasp the handle on the top of the cover and lift it 2. Fold the rear part of the luggage board frontward 3. Pull the luggage board hinge to the end of sliding slot and it will fall down lower to increase cargo space. 4. Slide it frontward (r ...

Kia Picanto JA 2017-2023 Owner's Manual: Battery capacity label

❈ The actual battery label in the vehicle may differ from the illustration. 1 AGM90LDIN : The Kia model name of battery 2 90Ah(20H R) : The nominal capacity (in Ampere hours) 3 170RC : The nominal reserve capacity (in min.) 4 12V : The nominal voltage 5 850CCA (SAE) : Th ...