Kia Picanto: Clutch System / Clutch Pedal

Kia Picanto JA 2017-2024 Service & Repair Manual / Clutch System / Clutch System / Clutch Pedal

Components and components location

Components

[Kappa 1.0 MPI / FFV, Kappa 1.2 MPI]

1. Clutch pedal assembly

2. Clutch cable

[Kappa 1.0 T-GDI]

1. Clutch pedal assembly
2. Ignition lock and clutch switch
3. Master cylinder

4. Clutch regulator
5. Clutch tube

Repair procedures

Replacement

[Kappa 1.0 MPI / FFV, Kappa 1.2 MPI]

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Loosen the clutch cable adjust nut (A) and then separate the clutch cable

3.	Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel")

4.	Remove the junction box. (Refer to Body Electrical System - "Junction Box (Passenger Compartment))

5.	Disconnect the cluch switch & ignition lock swtich connector (A).

6.	Pushing the clutch pedal and then remove the clutch cable (A).

Loosen the nuts (A) and then remove the clutch pedal.

Tightening torque :

9.8 - 14.7 N·m (1.0 - 1.5 kg·m, 7.2 - 10.8 lb·ft)

8.	Install in the reverse order of removal.

[Kappa 1.0 T-GDI]

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel")

3.	Remove the junction box. (Refer to Body Electrical System - "Junction Box (Passenger Compartment))

4.	Disconnect the ignition lock & clutch switch connector.

5.	Remove the push rod end (A) from the clutch pedal.

6.	Remove the battery. G 1.0 T-GDI KAPPA (Refer to Engine Electrical System - "Battery")

7.	Remove the ECM. G 1.0 T-GDI KAPPA (Refer to Engine Control / Fuel System - Engine Control Module (ECM)")

Disconnect the reservoir hose (A) and clutch tube (B) from the clutch master cylinder after removeing the pin (C).

Do not spill brake fluid on the vehicle; it may damage the paint if brake fluid does contact the paint, wash it off immediately with water.

9.	Remove the clutch master cylinder (A) by turning it clockwise.

10.

Remove the clutch pedal (B) after loosening the mounting nuts (A).

Tightening torque :

9.8 - 14.7 N·m (1.0 - 1.5 kgf·m, 7.2 - 10.8 lb·ft)

11.	Install in the reverse order of removal.

Clutch Switch

Specifications Specifications Item Specifications Working voltage DC 12.5V Operating force Initial position : 0.25 ± 0.15 N ...

Clutch Cable

Components and components location Components [Kappa 1.0 MPI / FFV, Kappa 1.2 MPI] 1. Clutch pedal assembly 2. Clutch cable Repair procedures Removal 1.Turn ignition switch ...

Other information:

Kia Picanto JA 2017-2024 Service & Repair Manual: Engine And Transaxle Assembly

Repair procedures Removal • Use fender covers to avoid damaging painted surfaces. • To avoid damage, unplug the wiring connectors carefully while holding the connector portion. • ...

Kia Picanto JA 2017-2024 Service & Repair Manual: Windshield Wiper-Washer Switch

Repair procedures Removal 1.Disconnect the negative (-) battery terminal. 2.Remove the steering column upper and lower shrouds after loosening the screws. (Refer to Body - "Steering Column Shroud Panal") 3.Disconnect the wiper switch / washer switch connector (A). 4.Rem ...