Kia Picanto: ABS(Anti-Lock Brake System) / ABS Control Unit

Kia Picanto JA 2017-2024 Service & Repair Manual / Brake System / ABS(Anti-Lock Brake System) / ABS Control Unit

Components and components location

Components

1. ABS control module connector
2. ABS control module

3. ABS bracket

Repair procedures

Removal

1.	Turn ignition OFF and disconnect the negative (-) battery cable.

Remove the brake fluid from the master cylinder reservoir with a syringe.

•	Be sure to completely remove foreign substances from around brake fluid reservoir and cap before opening the reservoir cap. Otherwise, it may cause contamination of brake fluid and deterioration in braking performance.

•	Do not spill brake fluid on the vehicle as it may damage the paint. If brake fluid comes in contact with the paint, wash off immediately with water.

3.	Remove the air cleaner assembly. G 1.0 MPI (Refer to Engine Mechanical System - "Air cleaner") G 1.2 MPI (Refer to Engine Mechanical System - "Air cleaner") F 1.0 MPI (Refer to Engine Mechanical System - "Air cleaner")

4.	Loosen the bolt and then remove the CVVT oil control valve bracket (A) and connector bracket (B).

Disconnect the brake tubes from the ABS by unlocking the nuts counterclockwise with a wrench.

Tightening torque :

A : 12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)

B : 12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)

6.	Disconnect the ABS control module connector.

Loosen the nuts and then remove the ABS control module (HECU).

•	Never attempt to disassemble the ABS.

•	The ABS must be transported and stored in.

•	Never shock to the ABS.

Installation

1.	Install in the reverse order of removal.

2.	After installation, bleed the brake system.

3.	Conduct the Variant coding.

4.	Conduct the Auto Detected Sensor Calibration.

5.	Conduct the Longitudinal G Sensor Calibration.

Diagnostic procedure by using diagnostic device

Perform diagnostic procedure by using diagnostic device as shown below:

Connect self-diagnosis connector (16pins) located under the driver side crash pad to self-diagnosis device, and then turn the self-diagnosis device after key is ON.

Select the "vehicle model" and "ABS/ESC" on GDS vehicle selection screen, then select OK.

[Variant Coding]

[Auto Detected Sensor Calibration]

[Longitudinal G Sensor Calibration]

ABS(Anti-Lock Brake System)

Components and components location Components 1. ABS control module (HECU) 2. Front wheel speed sensor 3. Rear wheel speed sensor Description and operation Description This ...

Front Wheel Speed Sensor

Repair procedures Removal 1. Remove the wheel tire (A). Tightening torque: 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft) 2. Loosen the wheel speed sen ...

Other information:

Kia Picanto JA 2017-2024 Service & Repair Manual: Heater & A/C Control Unit(Manual)

Components and components location Components [NON ISG] Connector pin function No. Connector A Connector B 1 Low Battery 2 Common Illumination (+) 3 Ground HTD 4 Middle (Low) ISG Battery ...

Kia Picanto JA 2017-2024 Owner's Manual: Bulb replacement precaution

Please prepare bulbs with appropriate standards in case of emergencies. Refer to “Bulb Wattage” on page 9-04. When changing bulbs and sorts, first turn off the engine at a safe place, firmly apply the side brake and take out the battery's negative (-) terminal. WARNING Working on t ...