Kia Picanto: Tires/Wheels / Tire

Kia Picanto JA 2017-2022 Service & Repair Manual / Suspension System / Tires/Wheels / Tire

Repair procedures
Tire Wear
   
Using tires and wheels other than the recommended sizes can cause unusual handling characteristics and poor vehicle control, resulting in a serious accident.
1.
Measure the tread depth of the tires.
Tread depth [limit] : 1.6 mm (0.0630 in.)
2.
If the remaining tread depth (A) is less than the limit, replace the tire.
   
When the tread depth of the tires is less than 1.6 mm (0.0630 in.), the wear indicators (B) will appear.

Tire Rotation
Checking For Pull And Wander
If the steering pulls to one side, rotate the tires according to the following wheel rotation procedure.
1.
Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.

2.
If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.

3.
If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.

4.
If the steering continues to pull to the opposite side, replace the front wheels with new ones.

Removal
1.
Remove the valve core and deflate the tire.
2.
Remove the side of the tire bead area from the wheel using tire changing machine.

   
The tire bead should be broken approx. 90° from the valve side of the wheel. The bead breaker should not be set too deep.
Avoid tire/tool contact with the valve on dismount.
Dismount should end near the valve.
3.
Rotate the wheel clockwise.

Installation
1.
Apply tire soap or lubrication to the top and bottom tire beads.

2.
To fit the bottom bead, position the valve at the 5 o’clock position relative to the head on the tire changing machine.

3.
Place the tire on the rim so the bottom bead touches the edge of the rim after the valve (6 o’clock). Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to fit bottom bead.

4.
After bottom bead is on tire, rotate the rim until the valve is at the 5 o’clock position relative to the head on the tire changing machine. Push down on the tire at the 3 o’clock position and rotate the rim clockwise to fit the top bead.

5.
Inflate the tire until both beads seat.
Item
Specification
Front
Rear
Tire pressure
155/80 R13
230 kPa (33 psi)
210 kPa (30 psi)
175/65 R14
185/55 R15
195/45 R16
175/65 R14 (Eco pack)
250 kPa (36 psi)
T115/70 D15
420 kPa (60 psi)

Tires/Wheels
...

Wheel
Repair procedures Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque: 107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft) ...

Other information:

Kia Picanto JA 2017-2022 Service & Repair Manual: Front Driveshaft


Components and components location Components 1. Drive shasft (LH) 2. Drive shaft (RH) [RH] 1. BJ assembly 2. Clip 3. BJ boot band 4. BJ boot 5. Dynamic damper band 6. Dynamic damper 7. Shaft 8. TJ boot band 9. TJ boot 10. Spider assembly 11. Circlip 12. TJ housing 13. Circlip ...

Kia Picanto JA 2017-2022 Owner's Manual: Selecting a Child Restraint System (CRS)


When selecting a Child Restraint System for your child, always: Make sure the Child Restraint System has a label certifying that it meets the applicable Safety Standards of your country. A Child Restraint System may only be installed if it was approved in accordance with the ...

Copyright © www.kpicanto.com 2017-2022