Kia Picanto (JA): Driveshaft and axle / Rear Axle Assembly

Kia Picanto (JA) 2017-2026 Service & Repair Manual / Driveshaft and axle / Rear Axle Assembly

Components and components location

Components
[Disc type]

1. Tosion beam axle
2. Brake disc
3. Brake caliper

[Drum type]

1. Tosion beam axle
2. Drum brake

Repair procedures

Removal
1.
Remove the wheel tire (A).
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

2.
Remove the rear brake disc caliper.
(Refer to Brake System - "Rear Disc Brake")
3.
Disconnect the rear wheel speed sensor connector.

4.
Loosen the screw and then remove the rear brake disc.
Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)

5.
Loosen the bolts and then remove the hub (A) from the torsion beam axle.
Tightening torque:
49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.1 - 43.3 lb·ft)

6.
Install in the reverse order of removal.
[Drum type]
1.
Remove the wheel tire (A).
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

2.
Loosen the screw (A) and then remove the brake disc.
Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)

3.
Disconnect the wheel speed sensor connector.

4.
Loosen the bolts and then remove the hub (A) from the torsion beam axle.
Tightening torque:
49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.1 - 43.3 lb·ft)

5.
Install in the reverse order of removal.
Inspection
1.
Check the hub for cracks.
2.
Check the brake disc for scoring and damage.
3.
Check the rear axle carrier for cracks.

    Components and components location Components [RH] 1. BJ assembly 2. Clip 3. BJ boot band 4. BJ boot 5. Dynamic damper band 6. Dynamic damper 7.

    Specifications Specification Front Suspension Item Specification Suspension type MacPherson Strut Shock absorber Type General Valve Rear Suspension Item Specification Suspension type Couple Torsion Beam Axle Shock absorber Type General Valve Wheel & Tire Item Specification Front Rear Wheel Aluminum 5.

    Other information:

    Kia Picanto (JA) 2017-2026 Service & Repair Manual: Power Door Lock Switch

    Repair procedures Inspection 1.Check for continuity between the terminals. If there is an abnormality, replace the switch. Removal    • When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

    Kia Picanto (JA) 2017-2026 Service & Repair Manual: Smart Key

    Repair procedures Smart Key Smart Key Code Saving 1. Connect the DLC cable of KDS/GDS to the data link connector (16 pins) in driver side crash pad lower panel, turn the power on KDS/GDS. 2. Select the vehicle model and then do "Smart key code saving".

    Categories

     
    Copyright © 2026 www.kpicanto.com - 0.0328