Kia Picanto: Fuses And Relays / Junction Box (Passenger Compartment)

Kia Picanto JA 2017-2022 Service & Repair Manual / Body Electrical System / Fuses And Relays / Junction Box (Passenger Compartment)

Components and components location
Component Location
I/P Junction Box

Circuit (I/P Junction Box)

Description and operation
Description
Communication Network Diagram

Abbreviation
Explanation
ABS
Anti-lock Brake System
ACU
Airbag Control Unit
AEB
Autonomous Emergency Braking
B-CAN
Body Controller Area Network
BCM
Body Control Module
C-CAN
Chassis Controller Area Network
CLU
Cluster Module
DATC
Dual Automatic Temp Control
EMS
Engine Management System
ESC
Electronic Control Suspention
EVP
Eva Vacuum Pump
I-BOX
Telematics System
LPI
Liquid Petroleum Injection
H_U
Head Unit (Audio / AVN)
M-CAN
Multi media Controller Area Network
MDPS
Motor Driven Power Steering
PGS
Parking Guide System
SLM
Seat belt remind & Lighting Module
SMK
Smart Key Unit
TCU
Transmission Control Unit
TMU
Telematics System
TPMS
Tire Pressure Monitoring System

Repair procedures
Fuse Inspection
1.
Check that the fuse holders are loosely held and that the fuses are securely fixed by the holders.
2.
Check that each fuse circuit has the exact fuse capacity.
3.
Check the fuses for any damage.
   
If a fuse is to be replaced, be sure to use a new fuse of the same capacity. Always identify the cause of the blown fuse and completely eliminate the problem before installing a new fuse.
Diagnosis with KDS/GDS
1.
The Interior Junction Block can be diagnosed by using the KDS/GDS. The Interior Junction Block communicates with the KDS/GDS which then displays inputs and outputs along with codes.
2.
To diagnose the Interior Junction Block function, select the vehicle model, Interior.
3.
To consult the present input/out value of Interior Junction Block, "Current DATA". It provides information of Interior Junction Block input/output conditions.

4.
To perform functional test on Interior Junction Block outputs, select "Actuation Test"

Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Lower Panel")
3.
Disconnect the connectors (A) from the fuse side of the interior junction block.
4.
Remove the interior junction block wiring mounting clip (B).

5.
Remove the interior junction block side connectors (A).

6.
Remove the interior junction block (A) after loosening the mounting nuts.

7.
Disconnect the connectors (A) from the back of the interior junction block.
8.
Remove the interior junction block wiring mounting clip (B).

Installation
1.
Install the interior junction block.
2.
Connect the interior junction block connectors.
3.
Install the crash pad lower panel.
4.
Connect the negative (-) battery terminal.
5.
Check that all systems operate properly.
Junction Box (Engine Compartment)
Components and components location Component Location E/R Junction Box Circuit (E/R Junction Block) E/R Junction Box Circuit (E/R Junction Block) Repair pr ...

Headlamp Leveling System
Components and components location Component Location 1. Headlamp leveling actuator 2. Headlamp leveling switch ※ headlamp leveling actuator is built into the headlamp. ...

Other information:

Kia Picanto JA 2017-2022 Owner's Manual: Ignition switch position


LOCK The steering wheel locks to protect against theft. The ignition key can be removed only in the LOCK position. After parking the vehicle, if driver’s door is opened without removing the ignition key at lock or ACC position, warning chime will alarm you to remove the key. Once ...

Kia Picanto JA 2017-2022 Owner's Manual: Automatic transaxle fluid


Checking the automatic transaxle fluid level The automatic transaxle fluid level should be checked regularly. Keep the vehicle on level ground with the parking brake applied and check the fluid level according to the following procedure. 1. Place the shift lever in N (Neutral) posit ...

Copyright © www.kpicanto.com 2017-2022